Latest effective Cisco 300-180 exam dumps, online Cisco 300-180 Practice Test

Actual effective Cisco 300-180 Exam dumps! Select Pass4itsure 300-180 VCE dump or 300-180 PDF dump to help you pass the first exam,
we carefully follow realistic exam Q&A, these questions and answers are frequently updated and industry experts review,
which will ensure that your 300-180 exam 100% Pass.Download valid pass4itsure 300-180 dump
VCE and PDF! https://www.pass4itsure.com/300-180.html (381 Q and dump)

[PDF] Free Cisco 300-180 dumps download from Google Drive:
https://drive.google.com/open?id=1FBNRkv6jQipAo3uUxeJ8BU8zubnj9kHe

[PDF] Free Full Cisco dumps download from Google Drive:
https://drive.google.com/open?id=14StRvSrOCPrIw-CKgAp7g-fLAIEFV1yM

300-180 DCIT – Cisco:https://www.cisco.com/c/en/us/training-events/training-certifications/exams/current-list/dcit.html

Pass4itsure offers the latest Cisco 300-180 practice test free of charge (50Q&As)

QUESTION 1
Refer to the exhibit.

When suspending or deleting VSANs, which three statements are true? (Choose three.)
A. You can delete only one VSAN at a time.
B. You must wait 60 seconds after you enter the vsan suspend command before you enter another command.
C. You must wait 120 seconds after you enter the vsan suspend command before you enter another command.
D. You can unsuspend only one VSAN at a time.
E. You can delete multiple VSANs as long as they are in the same domain.
F. You can delete multiple VSANs as long as they are in the same zone.
Correct Answer: ABD

QUESTION 2
Refer to the output.
feature otv
otv site-vlan 2
otv site-identifier 256
!
interface ethernet 2/0
ip address 192.0.2.1/24
ip igmp version 3
!
interface ethernet 2/1
ip address 192.0.2.2/24
ip igmp version 3
!
interface Overlay1
otv control-group 239.1.1.1
otv join-interface ethernet 2/0
otv extend-vlan 3-100
!
interface Overlay2
otv control-group 239.1.1.1
otv join-interface ethernet 2/1
otv extend-vlan 101-115
Which command best represents where the control plane configurations are applied?
A. switch(config-if-overlay)# otv isis hello-interval 30
B. switch(config-if)# otv isis hello-interval 30
C. switch(config-vlan)# otv isis hello-interval 30
D. switch(config)# otv isis hello-interval 30
Correct Answer: A

QUESTION 3
Refer to the exhibit.

A customer is having a problem with NPV. Which of these is the cause of the problem?
A. No server was requested or received by the FLOGI database.
B. One external link must be up for server interface to be up.
C. Multiple external links must be up for the server to come up.
D. Internal links are down and must be up for the server interface to be up.
Correct Answer: B

QUESTION 4



Which statement is true regarding the port channel 100 and 101 configurations between the Nexus 7010 switches?
A. The vPC assignments on N7010-C2 are incorrectly swapped
B. N7010-C1 is not allowing any active VLAN traffic to pass on Po100 and Po101.
C. LACP is not configured to initiate negotiations.
D. The vPC peer-keepalive is down between the two Nexus 7000 switches.
Correct Answer: A

QUESTION 5
Which three of these would cause two switch fabrics not to merge? (Choose three.)
A. Two or more switches do not have at least one assigned domain ID in common.
B. Two switches have different assigned VSANs on the connecting ports.
C. Two switches have different assigned VLANs on the connecting ports.
D. The static domain ID does not override the dynamic ID.
E. The election of the static domain is only determined by the WWNs of the two switches.
F. The physical connectivity between the two switches is not active.
Correct Answer: ABF

QUESTION 6
OTV is configured ?test pings confirm that it is working but other tests do not seem to perform well. What is the problem?
A. VLANs are not properly extended.
B. The multicast groups are not defined properly.
C. The transport network is not configured to process the overhead that is introduced by OTV.
D. The overlay may not be enabled.
Correct Answer: C

QUESTION 7
You are attempting to configure boot from SAN on your server that is attached to a Cisco MDS 9148 Fibre Channel switch. What is a possible issue that may occur?
A. Check the status of the licenses on the Fibre Channel switch.
B. NPV is not configured on the Fibre Channel switch.
C. NPIV is not configured on the Fibre Channel switch.
D. Boot from SAN is not supported via the Fibre Channel protocol.
Correct Answer: C

QUESTION 8
When you ping your new Cisco Nexus 7010 Switch, you see this output:
!!…!!…!!…!!…!!…
What could be the problem?
A. Traffic may be taking a bad route through the network.
B. HSRP is flapping.
C. CoPP is rate-limiting the pings.
D. The switch has high CPU utilization.
Correct Answer: C

QUESTION 9
If no traffic was ever sent across the overlay, what will the show mac address-table command on the OTV VDC indicate?
A. invalid command
B. the MAC address of the local OTV join interface
C. the system IDs of all the local OTV edge devices
D. the system IDs of all the local and remote edge devices in the overlay
E. all the MAC addresses learned on the extended VLAN
Correct Answer: B

QUESTION 10
Why do the lists not contain the same switches, after you issue the commands show cfs peers name and show cfs merge status?
A. The merge cannot occur until the VSAN IDs are synched.
B. The Cisco Fabric Services fabric has a physical port fault that should be investigated.
C. The fabric is partitioned into multiple Cisco Fabric Services fabrics.
D. Cisco Fabric Services need to be restarted to see the new switches.
E. A Cisco Fabric Services database lock has prevented the merge.
Correct Answer: C

QUESTION 11
Which command would you use to find the AED of an extended VLAN in a dual-homed site of an OTV network?
A. show otv aed on the AED
B. show otv site on any edge devices in the site
C. show otv vlan on the AED
D. show otv aed on any edge devices in the site
E. show otv vlan on any edge devices in the site
Correct Answer: C

QUESTION 12
Refer to the exhibit

An administrator sets up a FabricPath network. The administrator tries to ping between two SVI interfaces on the leaf switches 10 and 20, but it fails. What caused the pings to fail?
A. Switches S10 and S20 do not have F2 modules.
B. The vPC peer gateway must be enabled on switches S10 and S20.
C. Switches S1, S2, and S3 should be interconnected directly.
D. VLAN 10 is not enabled on the spine switches (S1, S2, and S3).
E. Layer 3 over a vPC+ peer link is not supported.
Correct Answer: D

QUESTION 13
Which two commands will show all the OTV edge devices and their MAC addresses in the local site? (Choose two.)
A. show otv overlay
B. show otv site
C. show otv vlan
D. show otv adjacency
E. show mac address-table
Correct Answer: BD

QUESTION 14
Which command on a Cisco Nexus 5000 Series Switch will show the interface information for port 10 on the connected FEX 100?
A. show interface Ethernet 100/10
B. show fex 100 interface Ethernet 1/10
C. show interface Ethernet 100/1/10
D. show interface Ethernet 1/100/10
Correct Answer: C

QUESTION 15
What are three situations that may cause an ISSU failure? (Choose three.)
A. A module is removed while the upgrade is in progress.
B. A proper ISSU license is not in place.
C. The device has a power disruption while the upgrade is in progress.
D. A line card is in a failure state.
E. The specified system and kickstart images are not compatible.
F. The management interface is not in the correct VRF.G. The secondary supervisor is not installed.
H. The redundancy force-switchover command was used during the ISSU.
Correct Answer: CDE

QUESTION 16
Which command helps to determine if there are any conflicts in the network with respect to a FabricPath configuration?
A. show licenses
B. show fabricpath conflict
C. show fabricpath conflict all
D. switchport mode fabricpath
Correct Answer: C

QUESTION 17
Your customer has a dual Cisco Nexus 7010 Switches in its data center. Customer’s representatives want to know how to determine if Cisco IOS ISSU is possible on the switches as they are upgrading to version 6.0.4. Which command is
useful to determine if the upgrade will be non-disruptive?
A. N7010-C1# show system redundancy ha status
B. N7010-C1# show incompatibility system
C. N7010-C1# install all
D. N7010-C1# show issu test bootflash:n7000-s1-system.6.0.4.bin
Correct Answer: C

QUESTION 18
Which option describes why the merge status for any application shows “In Progress” for a prolonged period of time when a new switch is added to the fabric?
A. The new switch must be upgraded to match the same version of code as the original switch.
B. The ports between the switches are not trunking all VSANs.
C. The application needs to be started on both switches.
D. There are outstanding changes that must be committed.
E. The merge status cannot occur until a copy running-config startup-config is done.
Correct Answer: D

QUESTION 19
Which three statements are true regarding trunking on an ISL between two switches in order for the VSAN to be trunked? (Choose three.)
A. The VSAN must be defined on both switches.
B. The VSAN must be on the VSAN allowed list.
C. All VSANs that are being trunked must be using either enhanced or non-enhanced mode zoning, but not both.
D. IVR must be configured for Cisco Fabric Services.
E. The device alias database must successfully merge.
F. There cannot be any duplicate domain IDs within an individual VSAN.
Correct Answer: ABF

QUESTION 20
Refer to the exhibit.

An administrator is deploying FCoE; however, a VFC interface will not come up. The administrator executes the commandshow platform software fcoe_mgr info interface vfc and displays the output.
What is the problem?
A. An incorrect VSAN number is being used.
B. The connected host does not support FIP.
C. FCoE is not enabled.
D. Priority flow control is not being negotiated with the converged network adapter.
Correct Answer: B

QUESTION 21



Cisco UCS users residing behind N5K2 are complaining about poor performance with a single LAN application in the data center. Which statement best explains what is wrong with N5K2?
A. Traffic balancing is based on the destination IP address.
B. Port channel members do not have equal bandwidths.
C. The trunk between the Nexus 5000 switches is filtering all VLANs.
D. E2/1 on N7010-C2 is not configured as a trunk for application traffic from N5K2.
Correct Answer: A

QUESTION 22
You receive a priority 1 trouble ticket that there is OSPF route instability in the data center core Cisco Nexus 7018 Switches. Which command is useful to help validate a theory that hello packets are being throttled?
A. N7018# show class-map interface control-plane
B. N7018# show policy-map interface control-plane
C. N7018# show service-policy interface control-plane
D. N7018# show copp status
E. N7018# show copp statistics
F. N7018# show control-plane class copp-system-class-critical
Correct Answer: B

QUESTION 23
You have enabled configuration synchronization between two Cisco Nexus 5548UP Switches. You create a port channel on switch 1 and determine that it was not synchronized with its peer. The peer switch can be pinged on the
management VRF. When you check your peer status, you receive a “peer not reachable” message in the command output. What is the explanation for this?
A. CDP is disabled.
B. An LACP mismatch exists on the peer interfaces.
C. UDLD is disabled.
D. CFSoIP is disabled.
E. Multicast routing is enabled.
Correct Answer: D

QUESTION 24
While troubleshooting HSRP adjacency, a packet analyzer captures the remote packet with the information: IP 224.0.0.102 with a MAC address of 0000.0C9F.0256. The DCI local group number is 256.
Which solution resolves the problem?
A. Request that the remote data center change the HSRP version to V1.
B. Report the issue as a suspected bug because the group number is correct based on the analyzer.
C. Request that the remote data center verifies that they do not have an HSRP password configured.
D. Request that the remote data center to use the correct HSRP group number.
E. Change the local HSRP version to V1.
Correct Answer: D

QUESTION 25
Which two commands will show all the OTV edge devices and their MAC addresses in all sites in the overlay? (Choose two.)A. show otv adjacency overlay
B. show otv site
C. show otv vlan
D. show otv adjacency
E. show mac address-table
Correct Answer: AD

QUESTION 26
Refer to the exhibit.

When your customers have NPV problems, which three actions should you take? (Choose three.)
A. Verify that the NPV core switch supports NPIV and that it is enabled.
B. Verify that all ports are properly configured and connected.
C. Ensure that the VLAN values are configured on both sides of the NPV core switch.
D. Verify the status of the servers and external interfaces, using the show npv server status command.
E. Ensure that the VSAN value that is configured on the device links is correct.
F. For all the device links, ensure that the port mode on the NPV device is in Full_port mode.
Correct Answer: ABE

QUESTION 27
To ensure that DCBX can be run on a switch, which other feature must be enabled?
A. Cisco Discovery Protocol
B. LLDP
C. Fibre Channel
D. IEEE 802.1ad
Correct Answer: B

QUESTION 28
Which command displays the traffic statistics for a port channel interface?
A. show interface port-channel channel-number
B. show port-channel traffic
C. show port-channel usage
D. show port-channel compatibility-parameters
Correct Answer: B

QUESTION 29
A customer calls you to report that it receives an error when entering the pinning max-links 4 command in FEX configuration mode on its Cisco Nexus 5596T Switch. Which of these is a likely cause for this condition?
A. The FEX fabric interface is down.
B. The transceiver is incorrect.
C. A fabric interface is in a port channel.
D. The fabric interface switchport mode is set to Access.
E. Only two fabric interfaces are connected.
Correct Answer: C

QUESTION 30
NPV mode is not operating properly on a Cisco Nexus or Cisco MDS Series Switch. What are two reasons? (Choose two.)
A. An uplink NP port is stuck initializing.
B. The VSAN does not match at each end of the connection.
C. The VLAN does not match at each end of the connection.
D. The license is invalid.
Correct Answer: AB

QUESTION 31
Which two statements about configuring NPV are true? (Choose two.)
A. Only F, E, and SD ports are supported in NPV mode.
B. Only targets can be connected to an NPV device.
C. Distribute the NPV core switch links to different port groups for improved scalability.
D. If DPVM is configured on the NPV core switch for an end device that is connected to the NPV device, then that end device must be configured to be in the same VSAN.
E. NPV does not support NPIV-capable module servers (nested NPIV).
Correct Answer: CD

QUESTION 32
When using a Cisco Nexus 5500 and Cisco Nexus 7000 Series Switch, how can a port channel interface be configured?
A. Layer 3 interface
B. Layer 3 interface in non-admin VDC only
C. Layer 3 interface in admin VDC only
D. Layer 3 interface in VDC 1 only
Correct Answer: A

QUESTION 33
Which two commands can you issue on a Cisco Nexus 5548UP Switch to determine which interfaces are connected to fabric extenders? (Choose two.)
A. show fex-fabric interface
B. show fex
C. show fex fex-id
D. show fex interface
E. show fex detail
Correct Answer: CE

QUESTION 34
Refer to the exhibit. Which two issues cause a problem with the implementation of an OTV between data centers? (Choose two.)

A. incorrect control-group address
B. incorrect data-group range
C. overlapping control-group and data-ranges
D. incorrect MTU
E. incorrect IGMP version
Correct Answer: CE

QUESTION 35
The traffic across your port channels seems to be favoring one link over the other. How can you adjust the load-balancing policy to include source and destination MAC addresses, IP address, and TCP port?
A. kcdc-5010-1(config-if)# port-channel load-balance ethernet source-dest-port
B. kcdc-5010-1(config-if)# port-channel load-balance ethernet source-dest mac ip port
C. kcdc-5010-1(config)# port-channel load-balance ethernet source-dest-port
D. kcdc-5010-1(config)# port-channel load-balance ethernet source-dest mac ip port
Correct Answer: C

QUESTION 36
Refer to the exhibit.

What is the cause of the ISSU failure when using the command show system internal csm global info?
A. The command conf-t is holding a lock and not released it.
B. The SSN feature is not enabled on both switches.
C. The reference count is less than 1 due to a lack of successful config-sync.
D. It cannot be determined from the output.
E. An Administrator is logged in on another session and has a lock of the session data base to prevent ISSU.
Correct Answer: A

QUESTION 37
Which two commands are used to determine the CoPP profile used on Cisco Nexus 7000 Series? (Choose two.)
A. #show copp profile
B. #show copp diff profile
C. #show copp status
D. #show running-config copp
E. #show policy-map interface control-plane
Correct Answer: CD

QUESTION 38
The installation of a new OTV network connecting two data centers via a service provider LAN has failed verification steps. Which statement explains why certain types of data are not being successfully transferred across the OTV network?
A. The number of extended VLANs across all configured overlays may be greater than 256.
B. The number of MAC addresses on either edge device may exceed 4000.
C. The additional 42-byte OTV overhead, along with the DF bit being set, may cause the service provider to drop packets based on their 1500 MTU settings.
D. Having more than two edge devices per site is not supported.
Correct Answer: C

QUESTION 39


FCoE traffic from C200-1 on VSAN 13 is not being switched through the network. Which statement explains the cause of the problem?
A. The LAN switchport on N5K2 must be configured as a trunk.
B. VLAN 1013 on N5K2 is not allowed on the LAN.
C. The vFC on N5K2 that is associated with VSAN 13 is in the wrong port mode.
D. The M1 card on the Nexus 7000 switch does not support FCoE.
Correct Answer: D

QUESTION 40
What are three reasons that could cause fabric merge problems in a Cisco SAN? (Choose three.)
A. Failure occurs when a switch supports more than 2000 zones per VSAN but its neighbor does not.
B. All devices are in the same VSAN.
C. The merged fabrics contain inconsistent data that could not be merged.
D. Both host and storage are logged in to the same SAN.
E. Small configurations may wipe out the large configurations.
F. The VSAN database is error-disabled.
Correct Answer: ACE

QUESTION 41
There is an ARP storm in VDC 1. Some users on VDC 2 notice that ARP is not resolving for their gateway on the Cisco Nexus core. What is the cause?
A. The ARP CoPP class committed information rate is exceeded, resulting in ARP loss in all VDCs.
B. The administrator has not correctly configured the ARP CoPP class in VDC 2.
C. The ARP traffic in VDC 1 is copied to the host ports in VDC 2, causing overutilization and output discards.
D. Because the ARP process in the default VDC (VDC 1) is responsible for processing ARP traffic for all VDCs, VDC 2 will be affected.
Correct Answer: A

QUESTION 42
A customer reports that a 10-Gb interface between a Cisco Nexus 7009 Switch and a Cisco Nexus 5548UP Switch is not passing traffic. The Nexus 7009 interface indicates up/up. The Nexus 5548UP interface indicates up/down. Which
feature should you enable to help isolate the root cause?
A. CDP
B. GOLD
C. UDLD
D. DAI
E. LACP
Correct Answer: C

QUESTION 43
What is one requirement for running FabricPath on a Cisco Nexus 7000 Series switches?
A. You must have an F Series module
B. You must run NX-OS version 4.2 to run FabrciPath
C. ISSU needs to be disabled to run FabricPath
D. LAN_TRANSPORT_SERVICES_PKG license needs to be installed to run FabrciPath
Correct Answer: A

QUESTION 44
Which three commands will help an administrator identify any issues with an In-Service Software Upgrade? (Choose three.)
A. show cts interface
B. show incompatibility system
C. show license file
D. show install impact all
E. show lacp issu-impact
F. show install issu-failure
Correct Answer: BDE

QUESTION 45
Refer to the exhibit.

The server port connected to the NPV edge switch does not come online. Which action should fix the problem?
A. Move the NP ports on the NPV edge and the F ports on the NPIV into the same VSAN 99.
B. Move the NP ports on the NPV edge and the F ports on the NPIV in the default VSAN 1.
C. Move all the ports into VLAN 1.
D. Move all the ports into VSAN 99.
E. Move all the ports into VLAN 99.
Correct Answer: A

QUESTION 46
Which CLI command can tell which switch is on the other side of port channel 2 that is trunking VSAN 5?
A. show topology vsan 5
B. show interface port-channel 2 trunk vsan 5
C. show interface port-channel 2 vsan 5 peer-info
D. show fcs vsan 5
E. show fspf database vsan 5 interface port-channel 2
Correct Answer: A

QUESTION 47
Refer to the exhibit. An administrator sees this message in the log while merging switch fabrics. What is the issue?

A. Two switches have different zone names with the same members.
B. Two switches have different zone set names with the same members.
C. Two switches have the same zone set and zone name, but with different members.
D. Two switches have the same zone set and zone name with the same members.
Correct Answer: C

QUESTION 48
A customer is troubleshooting FCoE in its network. They have discovered that vFC is currently down and there is no active STP port state on the bound Ethernet interface. What should the STP port state be to correct this issue?
A. The bound interface should be in an STP forwarding state for the native VLAN only.
B. The bound interface should be in an STP learning state for both the native VLAN and the member FCoE VLAN that is mapped to the active VSAN.
C. The bound interface should be in an STP forwarding state for both the native VLAN and the member FCoE VLAN that is mapped to the active VSAN.
D. The bound interface should be in an STP blocking state for both the native VLAN and the member FCoE VLAN that is mapped to the active VSAN.
Correct Answer: C

QUESTION 49



t has been determined that unknown unicast, multicast, and broadcast traffic is not correctly being switched through either Nexus 7010 switch. Which statement best describes the cause of this issue?
A. No VLANs are allowed across the vPC peer link.
B. The MST STP is not enabled on either switch.
C. The default VLAN is inactive.
D. VTP is not configured to handle this type of traffic.
Correct Answer: B

QUESTION 50
You receive an error attempting to enable the vPC feature on a Cisco Nexus 7018 Switch. Which Cisco Fabric Services distribution must be operational before the feature can be enabled?
A. CFSoFC
B. CFSoIP
C. CFSoV
D. CFSoE
E. CFSoM
Correct Answer: D

Conclusion:

Now, try the Pass4itsure 300-180 dumps for 100% passing your 300-180 exam — https://www.pass4itsure.com/300-180.html
(381 Q&As VCE Dumps and PDF Dumps)

[PDF] Free Cisco 300-180 dumps download from Google Drive:
https://drive.google.com/open?id=1FBNRkv6jQipAo3uUxeJ8BU8zubnj9kHe

[PDF] Free Full Cisco dumps download from Google Drive:
https://drive.google.com/open?id=14StRvSrOCPrIw-CKgAp7g-fLAIEFV1yM

Why Pass4itsure?

related: https://www.examdemoprogram.com/latest-updated-cisco-400-251-dumps-ccie-security-exam/